Category Archives: Fgtech Galletto

No image available

Renault Sirius 32N Immo off using Fgtech Galleto V54

As titled, here’s the wiring connection pinouts to Renault IMMO Off using Fgtech galletto 4 V54master ecu programmer. Renault Siemens Sirius 32N in boot mode     http://www.obdii365.com/wholesale/v54-fgtech-galletto-4-master-bdm-tricore-obd-function.html

No image available

Fiat Marelli ECU Wiring Pinouts to Fgtech Galletto

Look here: how to connect Fgtech galletto v54 master with a Marelli ECU on Fiat Marelli MJD 8F2  8DF  8DS – MPC5565 – FIAT DIESEL Marelli MULTIAIR 8GMF.A5 – MPC5565 – FIAT BENZINA Marelli MULTIAIR 8GMF.01 – SPC5553 – FIAT BENZINA MARELLI 7GF – MPC5554 – FIAT How to read/write Marelli ECU at a decent price: Working […]

No image available

Fgtech Galletto 4 V54 Master ECU Pinouts Collection

Here we sharing lots of wiring connection pinouts to Fgtech Galletto 4 V54 master ecu programmer. Tip: Click to enlarge. CAT challenger-ADEM IV Mercedes truck round diagnostic plug Mercedes truck plug year <2004 Sprinter/Actros/Atego/Axsor/ Econic/Class/Bredamenarini Bus BMW moto round diagnostic plug BMW moto round diagnostic plug 20  PIN Volkswagen truck Bosch EDC7C1 9 Poli Cummins VW Truck […]

No image available

Read and Write Bosch ECU MED17.5 with Fgtech Galletto

The ECU is built on the Infineon Tricore TC1766 processor. In the chip of the processor is a flash memory in volume of 1504 bytes and EEPROM in 32 bytes. There are two ways to read-write a block: via the OBD connector and through the BSL bootloader (the so-called boot-mode) Each of the methods has […]

No image available

How to Unlock Opel ME7.6.2 ecu

Here are solutions to unlock this ECU: Astra H 2.0 Bosch Me7.6.2. Q: Hello can tell me any good tool for reading opel ecu for chip tuning. Bosch ME.7.6.2 – Z16LET – Z14XEP Astra H and Corsa. Option 1: SMOK opel all from smok !!!! can help with this ecu Supported ECU CAN and available […]

No image available

How to Unlock VAG PCR 2.1 ECU with Fgtech Galletto on Bench

How to unlock SIMOS PCR 2.1 ECU from 2011 1.6 TDI VAG to remap on the bench using FG TECH galletto. How FGTech Galletto 4 V54 remap Simos PCR 2.1 ECU? Step1. Open Simos PCR 2.1 ECU, connect resistor and make jumper. Step2. Unlock Simos PCR 2.1 ECU on bench then close it. Step3. Put ECU inside […]

No image available

Guide: How to install Fgtech Galletto V54 on Windows 7

Fgtech Galletto 4 V54 Windows 7 has been tested to work perfect. But for some users, there are some troubles after Galletto v54 installation, e.g. Galletto 4 v54 won’t start/run after install. Here is the how-to’s and FAQs of Fgtech V54 Windows 7 installation. THE MOST IMPORTANT: You have to REMOVE ALL OLD FGtech FILES from the system […]

No image available

Fgtech Galletto 4 V54 China clone vs. EU Clone

This is FGtech Galletto 4 v54 PCB design and component position from EU to China. Galletto V54 EU clone: Eu pcb its Gold immersion and not hot air surface level like China. You can change a lot of parts but will not be the same FGtech Galletto 4 V54 china clone: Galletto V54 china version 1: Galletto […]

No image available

Fgtech, Ktag, Kess V2 unlock & flash PCR 2.1

This is a thread- “100% tested /worked bench unlock and flashing (read and write ) on pcr2.1”, posted in digital-kaos.co.uk. Good information, so i share this thread again. No one but yourself should take responsibility of what you will try. Big thanks to gzk in France did the following write-up of reviews of pcr2.1 bench […]

No image available

Fgtech Galletto V54 clone write safety PCR 2.1

Here is the instruction on writing stately PCR 2.1 with Fgtech Galletto 4 V54 master clone for those who do not have original tools.  All you need it’s UPA USB and Galletto V54 China clone! Credits to Mr. mercas who made this tutorial. On forum exist a lot of threads with bricked ecu’s because Galletto,Kess […]