No image available

How to Repair BMW E46 AUC Sensor ZKE by Xprog 5.55

Not long ago I bought a device called XProg-M with software v5.55. The xprog 5.55 comes with a set of adapters for various blocks \ processors. (Note: Credit to Pifon077 &) I’ve tried it on a BMW. It’s an EWS 3 immo system with the mask of the 0D46J processor, and on the ZKE low block from the […]

No image available

Mini Pro TL866a and TL866CS programmer Reset

There are times when the Mini Pro TL866A/TL866CS programmer cannot be recognized by the operating system. This happens when the unstable power supply is used in the system unit, your intervention in the circuitry of the programmer, etc. , which leads to failure of firmware microcontroller programmer. In this case, the programmer can be put into the bootloader mode. […]

No image available

Seat change 130 bhp maps for 150 bhp ECU with Winols

Thread: Winols ecu tuning software…Map changes from pd 130 bhp to pd 150 bhp REMAP PD 130 TO PD 150 THIS PAGE DOES NOT TELL YOU HOW TO REMAP A PD 130 TO 150 BHP. IT IS A COMPARISON OF SEAT LEON PD 130 & PD 150 FUEL AND TURBO MAPS. THIS COMPARISON SHOWS HOW SEAT CHANGED […]

No image available

How to repair BMW FRM3 with Xprog Step by Step

There is a problem that many people have heard about (and many have also met with it). Your BMW completely refuses outdoor lighting (more precisely, the passing beam and dimensions with the ignition on, but we can not control it), front windows do not work, central locking, interior light either. When diagnosed, the FRM does […]

No image available

Xprog Read EEPROM 95640 and Repair BMW E90 Airbag

Here’s the methods of removing the crash from the airbag units. Crash is a record appearing in the airbag blocks after an accident that caused the firecrackers to fire.   (Note. The tutorial is just for education purpose. You are at your risk. Credit to Russian expert evg3n175)   It’s a BMW 3 series E90. The previous […]

No image available

Will MPPS ecu flasher do ECU checksum?

MPPS V18 ECU Checksum Tutorial:   What is a checksum: A checksum is a block of digital data that is used to verify the contents is of the memory is correct.  Upon modifying the data the correct checksum must be calculated to ensure proper operation of the Engine Control Unit (ECU).   What happens if I […]

No image available

How to use WinOLS tuning to correct checksums

So here is a little tutorial – how to make checksums for ecu files with Winols tuning software, that should help all of you who don’t know how to do this get started using Winols. Winols 2.24 software download: http://blog.obdii365.com/2016/09/29/free-download-winols-v2-24-ecu-tuning-software/ Winols 1.5 cracked download: (tested 100%) http://www.obdii365.com/wholesale/winols-version-1-500-with-unlock-patch.html Checksums are very important, get them wrong and […]

No image available

How to Set up CG Pro 9S12 Programmer on Windows 7

New CG Pro 9S12 freescale programmer is come to replace CG100 Prog III. CG-Pro can change mileage on BMW, Mercedes-Benz and file make key on BMW, Land Rover and Porsche. Here’s guide on software download, installation and operation. Step 1: Download software Free download software on official website : http://www.cgprogcar.com/ Step 2: Install CGPro Setup Run CGPro_Setup as Administrator Click Next to install CG […]

No image available

How to use BDM100 to reset Kia Magentis II 2006 PCM

DIY guide: How to reset the PCM unit of the Kia Magentis II MG 2.0L MT 2006Y. A remarkable unit SIM2K-140 , which, for example, uses the PCMFlash to read the complete dump of flash memory AM29BDD160GD , from the address 0xh to the address 1FFFFFxh , and only calibrations are written. Actually, the story of the sad (relatively) case of replacing the calibrations in the […]

No image available

Ktag 7.020 Firmware Update Tutorial

Updating Ktag firmware to 7.020 version doesn’t block processor. For correct operation device it is necessary to change CID SDcard on 035344535330344780399b1368010300 This procedure is supported by not each SDcard. Programs for change of CID and the description of process easy to find in the Internet. I used mmc32 and evoplus_cid from github. This programs for linux. I haven’t found soft working […]