Category Archives: CG Pro

No image available

Read and Write EEPROM 93C66 with CG100 Prog III

CG100 Prog III will not only reset airbag/odometer but also read ECU/MCU/EEPROM. Here’s the guide to read and write EEPROM 93C66 by CG100. Remove 93c66 IC chip     Solder it to CG100 EEPROM adapter   Connect EEPROM adapter with CG100 Prog III, then connect CG100 pro with laptop via USB cable Open CG100 software, select Programmer […]

No image available

CG100 automatic repair Honda Airbag 77960-T9A-F411-M2

How-to:  repair Honda airbag using CG100 Prog III airbag reset tool. Model: Honda No.: 77960-T9A-F411-M2 Chip: R5F2154 Procedure: Power off vehicle Remove and disassemble the airbag computer, check srs type and chip In CG100 software, select Airbag function->Honda->77960-T9A-F411-M2 Check the wiring diagram, power on CG100 prog, connect CG-100 and airbag module following the wiring connection Reading airbag data […]

No image available

AT-200 Read BMW MSD85 MSD87 MSV90 ISN code

AT200 programmer is confirmed to work good with BMW MSD85 MSD87 MSV90 – able to read isn without any issue! Purpose: To check if the AT200 programmer is working or not source: http://www.obdii365.com/wholesale/bmw-at200-ecu-programmer.html Function for the test: Read ISN BMW DMEs for the test: MSD85 MSD87 MSV90 Steps: Step 1: install and run AT-200 programming software Step 2: connect […]

No image available

CGDI AT-200 review on BMW DME MSV90 Reading

AT-200 ecu programmer is a new solution to read/write/clone BMW ECU and read ISN code. Support almost all the BMW ECU model for reading and writing: MSV90 MSD85 MSD87 N2055 B38 B48.  Its best solution for changing used computer after broken (Only car computer repair essential. ) BMW AT-200 is able to read BMW ISN Code from DME when […]

No image available

How to change BMW X1 2010 CAS3 35080 Odometer by CG Pro?

Model: BMW X1 Year: 2010 Instrument type: 35080 Immobilizer: CAS3-0L15Y Device: CGPRO 9S12 programmer Purpose: odometer correction Original odometer: 191,245 km Step 1: Remove Dash Turn off ignition.  Remove and disassemble dashboard instrument         Locate chip m35080DOWQ   Step 2: Remove IMMO Box Remove immo box CAS3-0L15Y           Step 3: […]

No image available

CGPro Read Write Porsche 1N35H Success, VVDI Prog failed

Report:  A friend was trying to Read BCM porsche 2015 1N35H. MDP can Read but can not Write Xhorse VVDI Prog can not crack the MCU Finnaly he decided to test the CG Pro 9s12 programmer and here is the result. Step 1: Backup PFLASH Connect CG Pro with BCM follow the wiring diagram First need to […]

No image available

CGDI MB Renew Mercedes W164 ISM on Bench

How to: reset/renew Mercedes Benz W164 Siemens VDO ISM using CGDI Prog MB key programmer on bench. Follow cgdi prog wiring diagram to connect ISM unit with CGDI MB   In CGDI MB software, select Auto Computer, Module type W164->ISM/DSM/ESM Read ISM information Press Get to calculate erase password Erase password calculated successfully Press Erase Reset ISM success Done. http://www.obdii365.com/wholesale/cgdi-prog-benz-key-programmer.html

No image available

Read & Write 35160WT on BMW dashboard: Confirmed!

Question: Anyone tried with CG Pro 9s12 and 35160WT adapter ? Answer: I bought it just to try it… 160DOWT without Problems… 160DOWQ without Problems… Need the Adapter for WT For 35160WT, you need extra adapter and also to choose in options, you’ll have to connect this adapter on separate port… Information confirmed by http://www.obdii365.com/wholesale/cg-pro-35106wt-adapter.html From update log: Added Dashboard […]

No image available

CGDI Prog MB Renew ECU CR3.31 Virgin Reset Mercedes VITO

How to use CGDI Prog MB to virgin/blank Mercedes VITO Bosch ECU CR3.31.   Select Auto computer function, press Read to read module information CGDI MB read full info. Get erase password Get erase password successfully Press Erase Read module information again Now you can see the ECU is not persionalized nor actiavted. http://www.obdii365.com/wholesale/cgdi-prog-benz-key-programmer.html

No image available

Mercedes Bosch ME9.7 ECU Reset by CGDI Prog MB

How to Reset/Virgin Mercedes ECU with CGDI Prog MB key programmer.  Remove ECU from car, and connect according to the software wiring diagram Engine computer pin i.e Bosch ECU ME9.7 Open software,enter Auto computer,choose“Engine computer” Software wiring diagram Physical wiring diagram Click ”read” Engine computer related information Click to get erase password, calculated successfully Get the password successfully, […]