Category Archives: Kess V2

No image available

Where to Download Ksuite 2.47 for Kess V2 Clone?

Ksuite 2.47 software for Kess V2 firmware 5.017 clone free download resource is provided below: No need HWID and KG. Unpack DLL from archive in folder Ksuite/DLL.   Ksuite_2.47 for Kess v2 5.017 clone https://mega.nz/#!Sx8i3JQK!XC2WUVHJCSf3bKg4niJhyaL3444uz8GcSvCXmZi4jeI DLL https://mega.nz/#!C4kHVTzb!UOwqWrLM8-jr86MJLCLhZw-srYuAklVUOv0V6PPSSDA (Big thanks to svvag2000. You are at your risk)   Ksuite 2.47 FAQs: Q: This Ksuite 2.47 gives something extra out […]

No image available

Will Kess v2 ot Ktag read and write Abarth 124 Marelli 8GMK?

Purpose: Read a Magneti Marelli 8GMK from an Abarth 124 Optional ECU programming tool: Kess V2 firmware 5.017 and Ktag firmware 7.020 Basic info: 500x with same ecu is supported by Kess 5.017 (protocol 532), but 124 has a new protocol, the 576. Doubt: Is there a possibility to read it with this ksuite updated or users need a new Kess […]

No image available

Will MPPS V21 read VAG BOSCH EDC15P+ ECU on bench

Question before entering: I have some trouble with my spare EDC15P+ ECUs.  I have now invested in a MPPS V21 because of its booting capabilities!  But No matter what i do, MPPS keeps saying “Booting of ECU failed” or it freezes during connection establishment. I have tried this om 3 different ECU’s with bad flash and 2 PC’s. The […]

No image available

Free Ksuite 2.23 Winols 2.24 for Reworked Kess and KTag

Free download Kess v2/Ktag software Ksuite 2.23 and Winols 2.24: https://mega.nz/#!PoIm1DJL!G7m_TsNs8dMIiI1EmVc46uqHyFu7yFFcMKen37666qA Here you have full ksuite, with helps and internet protected   What is Ksuite? Ksuite is software to used with Ktag or Kess V2 to read and/or write ECUs. With KESS V2 you programming directly through the OBD port of the vehicle, while with Ktag  you […]

No image available

Volvo V70 EDC15C11 Read and Write by Kess, Ktag, MPPS or FgTech?

Here are optional solutions of Volvo V70 EDC15C11 ECU read and write using different ECU programmers, incl. Kess V2, Ktag, MPPS cable, FgTech Galletto 4 V54. Car: Volvo V70 D5 2004 163hp Ecu: I think the car has either a EDC15C2 or EDC15C11 ecu. (K-suite states EDC15C2) Option 1: You can use Fgtech Galletto V54 Rread/write work only […]

No image available

How to Turn Off Mazda RX-8 Speed Limiter by Kess V2

Here’s the turoial to disable the speed limiter on the Japanese ( JPN ) right-hand drive Mazda RX-8 SE 1.3L AT. Disclaimer: The guide was translated from Russian. It is only for education purpose. Credit to  P1on3R91. You are at your risk. In this car, a 180 km / h limiter is installed. It seemed it would be easier to turn it off. But […]

No image available

Kess V2 5.028 vs Kess V2 5.017

KESS V2 5.017 updated version – KESS V2 5.028 is gonna happen. So, what’s the difference between Kess V2 firmware 5.028 and Kess V2 firmware 5.017?   Here you go.   1- New firmware: 2018 Kess V2: firmware 5.028 2017 Kess V2: firmware 5.017   About components improvement: Kess V2 5.028: unknown components improvement Kess […]

No image available

Kess V2 read and write Renault Lagoon 3 EDC17CP58

Kess V2 manual: How to read/write Renault edc17cp58 ECU through BOOT: Note: When writing the modified file, the checksum of the data may last several minutes, depending on the performances of your computer. Preparation before Renault ECU read/write Remove the ECU from the vehicle; Open the ECU, taking care in not damaging the parts inside; Reconnect the […]

No image available

Ktag Kess V2 Full Set 22 BDM Probe Adapters List

The full set BDM probe adapters for KTAG, KESS V2, KTM100 Dimsport, Trasdata chip tuning tools is available in obdii365.com.   Function: To use with ECU programmers to read  Denso, Marelli, Bosch, Siemens ECUs. Features: Adapter width: ~60mm width for original BDM Probe, not for low quality plastic with 40mm width. Adapter thickness: 2mm Adapter colour: Green A full set comes with 22 […]

No image available

How to use Kess V2 Ktag to Unlock CRP3 LPC2478 via J-link

As you know, for crp3 we can do the trick for unlock crp3 heating on Ktag or Kess V2 programmer or buy a new NXP and write it (only one time) Here are some questions & answers on Google form, questions about “how will you use J-ink if its crp3 ?”… Q: Can I update NXP directly if at this […]