Category Archives: Ktag

No image available

Read Delphi MT80 by Ktag, Foxflash, CG100 or Others

There are some tools to read and write GM/Geely Delphi MT80/MT80.1 ECU. Delphi MT80 ECU usually has problems car not start, No fuel injection signals, No ignition signals, it’s a common problem can be repaired with ecu tools. The problem is the result of the data lost of the MCU, reprogramming the MCU or change a new MCU […]

No image available

What Tool to Read and Write Fiat Marelli IAW 7GF?

If any of the interfaces that I have can read this ECU Fiat Marelli IAW 7GF? Yes, there are some affordable ecu programmers to read and write IAW 7GF.     1.Foxflash  Fox flash will read and write IAW 7GF via jtag mode. FoxFlash Pinout to Fiat Marelli IAW 7GF MPC5554 Connect the multifunction cable […]

No image available

Read Alfa Marelli MM10JA by Foxflash, Kess V2 or Flex

What ecu programmer to read and write Alfa Romeo Marelli MM10JA MPC5777 ECU? via OBD, bench or boot mode?       Here top 5 tools are listed.     1). Cheapest option Foxflash programmer OBD mode: The built-in OBD does not working. It does not read the ECU ID nor read/write ECU. Boot mode: […]

No image available

Top Tools to Unlock FCA Chrysler GPEG2A ECU

How to unlock FCA Chrysler Jeep continental 2015+ GPEG2A ECU to use hptuner for tuning?  What tool is used?   Here’s the clue.   Hptuner: No Original hptuners also can’t unlock gpec2a, need send ecu for unlock. So does the clone MPM tool.     Foxflash/KT200: Recent update adds FCA GPEC2 GPEC3 GPEC4LM GPEC2A ECUs. foxFlash […]

No image available

PSA MEV17.4.2 Pinout to Foxflash and Ktag

Foxflash/KT200 will read, write and clone PSA MEV17.4.2 in both Bench and boot mode. It will do auto checksum.       Foxflash MEV17.4.2 bench pinout       To read and write use the following driver: → BENCH TRICORE → CITROEN / PEUGEOT → TC1767 – PSA → MEV17.4.2   Foxflash MEV17.4.2 boot pinout (Tricore […]

No image available

Ksuite 3.68 Download and Released Notes

(12.2019) Ksuite 3.68 download links: https://mega.nz/#!FkNDBSYC!qagszJqllai3YVPlQ4X0A0A-xyJC-jW67cpOYZgYe_c http://www.alientech.to/xnote/sw/KESSv2/Setup.exe IMPORTANT: IT’S RISKY to use the link now (15-12-2019) But sw is being tested. will update results here. Will test with Kess V2 fw 5.017 and Ktag fw 7.020… Before test result is out, you’re advised to use Ksuite 2.25 tested version: https://mega.nz/#!euYHRaBR!uF7cKkUpbNcK1C_ICvvbbtSTGlAFROZb7HH6vpjtT_E and Ksuite installation instruction for reference: […]

No image available

How to Solve Ktag Mandatory update Error by Token Reset?

Look here: Ktag 6.070 token issues SOLVED Ktag version: Ktag firmware version 6.070 Error message: ktag warning: mandatory update within the next 5 programming. connect the tool to the internet and run the update as soon as possible Solution: There are only 5 tokens left, so you need to reset tokens. You need: Reset tokens for Ktag. […]

No image available

What Device to Read and Write Mercedes SIM271 ECU?

Question: Need to swap a Mercedes SIM271 ECU. Any idea which tool can do it? Option 1:  BitBox Mercedes SIM271 Module BitBox is the module for reading and writing on the bench by CAN-bus for petrol Mercedes-Benz W204/W212 vehicles with Siemens/Continental SIM271 ECUs. The J2534 Tactrix Openport 2.0 interface, BitSoftware Senselock USB dongle and Universal […]

No image available

 Ktag help file and Wiring for Volvo Bosch EDC17

This is a Ktag help file used for Volvo Bosch EDC17 on GPT vehicles Warnings: your own risk! To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair. After opening the ECU and […]

No image available

What is new in Ktag firmware V8.000?

What is Ktag 8.000: The updated K TAG 8.000 programmer is designed for reading and writing control units for cars, motorcycles, trucks, agricultural machinery and boats. KTAG is used to program microprocessors in electrical circuits. The software has a clear interface and allows you to quickly master the work with the developer. Updated the firmware to version 7.020. Open All Protocols […]