How-to: change odometer on A Opel Astra H with digiprog 3 v4.94 mileage programmer. Need to remove dash   Locate EEPROM IC 35080     Connect chip IC with digiprog3 using clip adapter Select CAR/TRUCK->Opel/Vauxhall->Astra->35080       Digiprog3 prompts to connect with PLUG 1 Reading old mileage Manually enter new odometer you desired Writing new mileage Go back and […]

How-to: Toyota/Honda/Subaru Renesas H8SX UART airbag module reset using Diatronik OBD Tool and Gprog. What you need: Diatronik SRS OBD Tool/CarMasterX/GromCalcTool GPROG LITE SL adapter With Gprog adapter you can do Toyota Honda Subaru Renesas H8SX crash remove by solder points and read/write Renesas H8SX full flash by Jtag. Note: Gprog cannot work stand alone. It must […]

How-to: Kia Soul 2016 2015 2014 Airbag Module Reset via OBD CAN Lines.   Kia airbag control unit MOBIS 95910-B2010   Remove crash data from KIA Soul on the table via OBD cable using CAN Low and CAN High pins. No need to open unit up, no soldering. Or directly in the car no need to remove the module.     […]

Possible to use Digiprog 3 v4.94 for Porsche Cayman odometer correction? Yes. Here is the Cayman with chip types confirmed to work: Porsche Cayman 93C86 Porsche Cayman MCU 35P08 Porsche Cayman 2010 95640 Porsche Cayenne Diag In detail… Porsche Cayman 93C86 Note Tacho Meter Value Dismantle Tacho   Identify Chip 93C86 Desolder Chip 93C86 Clean Chip 93C86 Set […]

Yanhua ACDP Mini Wiring Diagram: Suitable for EEPROM 24 25 93 95 Series Used for in circuit (ICP)and on board(OBP)programming Features: No need to remove chip No need soldering No need to cut the line No need to lift the pin Wiring: How to use with OBP + ICP adapter Good to know where is: Patch (SOP) soldering […]

Questions:  I tried to correct the odometer on my BMW X5 2010 instrument.  But Yanhua Digimaster 3mileage programmer gave me error “This function is for testing by conner only. The formal issuance will be advised later.” Here was my operation picture uploads:           When i enter from Diagnostic socket adjustment, it gave […]

New test reported: Skoda Yeti NEC+24C64 VDO-12 odometer correction is done with OBDSTAR X300M mileage programmer via OBD. Here’s the operation carried out by OBDPROG MT401 which is the same as OBDSTAR X300M (OBDPROG is a branch of OBDSTAR).  OBDSTAR 300M is better than MT401, it updates to the newest car models while OBDPROG MT401 for older car […]

Yanhua Tech released a new 35160/35080 Programming Emulator to adjust mileage for following EEPROM models: M35080/M35080-3/M35080-6/M35080V6/M35080VP/080DOWQ/080DOWT/160DOWQ/160DOWT/35160WT EEPROM. Note: The simulator is stand-alone. No need to work with other software program or hardware. Here’s the guide to change mileage on M35160 eeprom, same operation goes to M35xxx series. Solder the 35XXX chip on the dash meter to the specificed location […]

Here are adapter schematics to original scorpio-lk Orange 5 programmer.   Orange-5 Connectors and Panels Adapters compatible with Orange2,3 are attached to connector SE. Microwire 93cXX Connections (DIP8,SOIC8,SOIC14) Adapter for reading ISO smart-card Adapter for Programming microcontrollers ATMEL AT89Cx051 Orange5 Adapter for serial programming of microcontrollers ATMEL AVR Instead of the quartz resonator reference frequency from terminal […]

There are times when the Mini Pro TL866A/TL866CS programmer cannot be recognized by the operating system. This happens when the unstable power supply is used in the system unit, your intervention in the circuitry of the programmer, etc. , which leads to failure of firmware microcontroller programmer. In this case, the programmer can be put into the bootloader mode. […]