Mazda3 and Mazda CX30 from year 2020 have S6J329CPLS Spansion mcu on Speedo. They are equipped with VISTEON cluster and have no EEPROM. Mazda 3 2020 cluster Picture from the other side of PCB. BTW, the needles does not have to be removed in this cluster to reach both sides of the PCB. […]
I share scripts to read Renesas RH850 MCU’s with Iprog+ using Serial Nº1, connections diagram also included. https://mega.nz/file/gA1AGSiS#c3C7drOrbwmshp6pPlXbTc_U0LvtKW8QLOCluDIt76M password: Archive password= w@wRoturbo_Renesas_RH850 Credits to @RoTor Roturbo R7F7010023 (512Kb+32Kb+32Kb).ipr R7F7010024 (512Kb+32Kb+32Kb).ipr R7F7010033 (936Kb+32Kb+32Kb).ipr R7F7010034 (936Kb+32Kb+32Kb).ipr R7F7010063 (1094Kb+64Kb+32Kb).ipr R7F7010064 (1094Kb+64Kb+32Kb).ipr R7F7010073 (1094Kb+64Kb+32Kb).ipr R7F7010074 (1094Kb+64Kb+32Kb).ipr R7F7010083 (256Kb+32Kb+32Kb).ipr R7F7010084 (256Kb+32Kb+32Kb).ipr R7F7010093 (384Kb+32Kb+32Kb).ipr R7F7010094 (384Kb+32Kb+32Kb).ipr R7F7010103 (512Kb+32Kb+32Kb).ipr R7F7010104 (512Kb+32Kb+32Kb).ipr R7F7010113 (256Kb+32Kb+32Kb).ipr R7F7010114 […]
I have xprog 5.55 clone a couple of years and never let me down mate. newer versions have issues. also upa clone, old but still good, tl866 clone, and orange too with little knowledge and searching in forum (DK or MMH) you can rework most of them and never have problems They are pretty cheap so I […]
There are two solutions to read and write PCF79xx: Iprog+ clone + PCF79XX SD-card adapter or Xhorse VVDI Prog programmer + PCF79XX Adapter Iprog+ clone + PCF79XX SD-card adapter √PCF7941 √PCF7952 √PCF7953 √PCF7961 Read and write the above PCF79XX chip through MSDA, MSCL lines. VVDI Prog + PCF79XX Adapter √PCF7922 √PCF7941 √PCF7945 √PCF7952 √PCF7953 √PCF7961 PCF79XX chip […]
Look here: difference between iProg Plus and CarProg Programmer iProg Plus CarProg Full Image Price (china clone) 109.00 usd 69.99 usd Update Free to update; Users can update iprog+ sw themselves FREE but new firmware required; Users cannot update carprog sw on their own Software version V80 (released in 2019) V10.93 (released in […]
Toyota Hilux not start, detected B2799 fault code (ECU immobilizer system error) using Launch X431 scanner. Read and repair ECU Immobilizer 89780-06130 data using iprog+ pro clone. Then erase fault codes. Now vehicle starts again. Picture attched below: http://www.obdii365.com/wholesale/iprog-pro-mileage-programmer.html
Here’s the run down step-by-step for newbies to install iProg+ Pro v76 driver software on Windows 7 32 bit. iProg V76 software download: https://share.weiyun.com/5FTr7zl password: fm63a3 Software version: iprog+ v76 (version 2019) Operating system: Recommend Windows 7 32 bit and 64 bit Iprog 76 installation instruction: (install iprog driver software, then run iprog app for use – no […]
Here, you can download iprog pro version 2018 & 2019. Link 1: unknown security! 2018 iprog pro download free: https://mega.nz/#!7LxjCRqD!53iXL6K3Ku_3SAzSN0-3po885aFJYLPSrnTyTYhr1Vg Link 2: tested successfully 2019 iprog pro crack download: http://www.obdii365.com/wholesale/iprog-pro-mileage-programmer.html operation system recommendation: Window 7 32 bit (need luck to install iprog+ v69 on Vista, Windows XP, Windows 8) tested by pros working for obdii365.com confirmed to work for airbag, […]
Look here: iProg Pro programmer original or clone? black or red? iProg pro original: price: 580 usd around iProg pro clone: fyi, there are two versions of cloned iprog programmers: one with a red look, the other with a black shell price: 350 usd around (200-300 usd cheaper) iProg pro clone in red: iProg pro clone in black: […]
Iprog+ pro clone has been tested and confirmed working perfectly on Windows XP. good at airbag reset, dashboard odometer correction, and a lot of programming. Here is iprog+ software installation instruction. iprog operating system: Windows xp: tested 100% Windows vista Windows 7 Windows 8 iprog pro price: around 500 usd (iprog clone) iprog+ software download: http://www.obdii365.com/wholesale/iprog-pro-mileage-programmer.html How […]