In increasing number of user already obtain Ksuite 2.53 to run with Kess v2 5.017 clone, and share their test reports, here obdii365.com would like to put these respective reviews together. – Tested this morning 2.53 ok reading audi a3 ppd … – Tested on WIN7 32bit and it’s working fine. I’ve read with KESS, a MED17.5.5 by OBD. I’ve […]
Latest Ksuite V2.53 software is verified working with Kess v2 firmware V5.017 online version. Software can be download here for free. What’s new in Kess V2 v2.53? Fixed bugs and added more car models. Free Download Kess v2 ksuite v2.53 software https://share.weiyun.com/5FPSb3H Password: i4cwgr (tested 100%) Mega link (not tested) https://mega.nz/#!Lol0GCZR!nOeibBrssBZGwzzvHAlNozrMV3VkVWIl9P0zBT6dcIo Advantages of v2.53 version over v2.23: […]
Today I was flashing the engine control unit on the Chevrolet Cruze A J300 2012Y 1.8L AT. The car arrived with errors after the service, where they changed the rear lambda, put a trick, checked the wiring, cut the cat, etc: The owner of the car is already tired of all this, so it was […]
Ksuite 2.47 software for Kess V2 firmware 5.017 clone free download resource is provided below: No need HWID and KG. Unpack DLL from archive in folder Ksuite/DLL. Ksuite_2.47 for Kess v2 5.017 clone https://mega.nz/#!Sx8i3JQK!XC2WUVHJCSf3bKg4niJhyaL3444uz8GcSvCXmZi4jeI DLL https://mega.nz/#!C4kHVTzb!UOwqWrLM8-jr86MJLCLhZw-srYuAklVUOv0V6PPSSDA (Big thanks to svvag2000. You are at your risk) Ksuite 2.47 FAQs: Q: This Ksuite 2.47 gives something extra out […]
Purpose: Read a Magneti Marelli 8GMK from an Abarth 124 Optional ECU programming tool: Kess V2 firmware 5.017 and Ktag firmware 7.020 Basic info: 500x with same ecu is supported by Kess 5.017 (protocol 532), but 124 has a new protocol, the 576. Doubt: Is there a possibility to read it with this ksuite updated or users need a new Kess […]
Free download Kess v2/Ktag software Ksuite 2.23 and Winols 2.24: https://mega.nz/#!PoIm1DJL!G7m_TsNs8dMIiI1EmVc46uqHyFu7yFFcMKen37666qA Here you have full ksuite, with helps and internet protected What is Ksuite? Ksuite is software to used with Ktag or Kess V2 to read and/or write ECUs. With KESS V2 you programming directly through the OBD port of the vehicle, while with Ktag you […]
Here’s the turoial to disable the speed limiter on the Japanese ( JPN ) right-hand drive Mazda RX-8 SE 1.3L AT. Disclaimer: The guide was translated from Russian. It is only for education purpose. Credit to P1on3R91. You are at your risk. In this car, a 180 km / h limiter is installed. It seemed it would be easier to turn it off. But […]
KESS V2 5.017 updated version – KESS V2 5.028 is gonna happen. So, what’s the difference between Kess V2 firmware 5.028 and Kess V2 firmware 5.017? Here you go. 1- New firmware: 2018 Kess V2: firmware 5.028 2017 Kess V2: firmware 5.017 About components improvement: Kess V2 5.028: unknown components improvement Kess […]
There are differences between the Kess V2 5.017 red pcb boards. Both work good? Let’s see the two boards here and read reviews to find out the truth. Kess V2 5.017 Version 1: Most of the boards look like this Kess V2 v5.017 Version 2: board with different reworked parts: 1.the left upper corner and the lower right corner notch size […]
What’s the exact difference between kess v2 slave or master? It’s better to buy original or clone are good? It all depends. Kess v2 good clone used be ok for older ecus only, but now also work great with newer ones. and with a slave you will have to rely on the master for your […]