There are some tools to read and write GM/Geely Delphi MT80/MT80.1 ECU. Delphi MT80 ECU usually has problems car not start, No fuel injection signals, No ignition signals, it’s a common problem can be repaired with ecu tools. The problem is the result of the data lost of the MCU, reprogramming the MCU or change a new MCU […]
If any of the interfaces that I have can read this ECU Fiat Marelli IAW 7GF? Yes, there are some affordable ecu programmers to read and write IAW 7GF. 1.Foxflash Fox flash will read and write IAW 7GF via jtag mode. FoxFlash Pinout to Fiat Marelli IAW 7GF MPC5554 Connect the multifunction cable […]
How to unlock FCA Chrysler Jeep continental 2015+ GPEG2A ECU to use hptuner for tuning? What tool is used? Here’s the clue. Hptuner: No Original hptuners also can’t unlock gpec2a, need send ecu for unlock. So does the clone MPM tool. Foxflash/KT200: Recent update adds FCA GPEC2 GPEC3 GPEC4LM GPEC2A ECUs. foxFlash […]
Foxflash/KT200 will read, write and clone PSA MEV17.4.2 in both Bench and boot mode. It will do auto checksum. Foxflash MEV17.4.2 bench pinout To read and write use the following driver: → BENCH TRICORE → CITROEN / PEUGEOT → TC1767 – PSA → MEV17.4.2 Foxflash MEV17.4.2 boot pinout (Tricore […]
The problem with some ECU’s, is that you can’t read them over OBD (except on some original/high priced tools) and for that reason you may need KTAG to read a full BDM, unlock TPROT (if it’s available), write the modifications back with KTAG and then you can use KESS over OBD to read/write. Here’s how it works in 4 […]
(12.2019) Ksuite 3.68 download links: https://mega.nz/#!FkNDBSYC!qagszJqllai3YVPlQ4X0A0A-xyJC-jW67cpOYZgYe_c http://www.alientech.to/xnote/sw/KESSv2/Setup.exe IMPORTANT: IT’S RISKY to use the link now (15-12-2019) But sw is being tested. will update results here. Will test with Kess V2 fw 5.017 and Ktag fw 7.020… Before test result is out, you’re advised to use Ksuite 2.25 tested version: https://mega.nz/#!euYHRaBR!uF7cKkUpbNcK1C_ICvvbbtSTGlAFROZb7HH6vpjtT_E and Ksuite installation instruction for reference: […]
Question:Can you read and write edc17c19 with fgtech galletto? Anyone have experience ?? I can’t find much info … Maybe somebody done with galetto and can give instructions ???Experience:1). Galletto works with this ECU without any problems, manual for tricore in app folder. 2). It is possible to read it in boot mode with galetto.3). Kess china […]
Look here: Ktag 6.070 token issues SOLVED Ktag version: Ktag firmware version 6.070 Error message: ktag warning: mandatory update within the next 5 programming. connect the tool to the internet and run the update as soon as possible Solution: There are only 5 tokens left, so you need to reset tokens. You need: Reset tokens for Ktag. […]
Question: Need to swap a Mercedes SIM271 ECU. Any idea which tool can do it? Option 1: BitBox Mercedes SIM271 Module BitBox is the module for reading and writing on the bench by CAN-bus for petrol Mercedes-Benz W204/W212 vehicles with Siemens/Continental SIM271 ECUs. The J2534 Tactrix Openport 2.0 interface, BitSoftware Senselock USB dongle and Universal […]
This is a Ktag help file used for Volvo Bosch EDC17 on GPT vehicles Warnings: your own risk! To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair. After opening the ECU and […]